Air Tools Compressor

The 2000QE is not just a pressure washer—it’s a thermal cleaning system. The combination of 2000 PSI pressure + 4.0 GPM flow + hot water up to 195°F makes it highly effective for: - Breaking down grease and oil without excessive pressure - Reducing chemical usage due to heat-assisted cleaning - Fas

1500-MX

$1,471.99

The 1500MX sits in the “sweet spot” between light commercial and industrial cleaning systems: - Much stronger cleaning force than 1000 PSI units - High flow (3.0 GPM) improves rinsing speed and detergent coverage - Better suited for grease, oil, and workshop dirt removal - Still safe for indoor or

1000XDE

$996.99

The 1000XDE is designed for controlled cleaning applications, not heavy surface stripping. At 1000 PSI with 2.2 GPM, it focuses on: - Strong rinsing and washing efficiency - Safe cleaning of equipment, vehicles, and facility surfaces - Continuous daily use in maintenance environments - Effective ch

1000WM/SS

$1,177.99

The 1000WM/SS is designed for controlled cleaning rather than high-impact stripping. At 1000 PSI with 2.2 GPM flow, it emphasizes: - Strong rinsing capability rather than cutting power - Safe cleaning for equipment, vehicles, and facility surfaces - Consistent performance during long daily use cycl

1000MX

$996.99

The 1000MX is not designed for heavy industrial stripping or paint removal. Instead, it focuses on controlled, safe cleaning power with steady flow. At 1000 PSI and ~2 GPM, the machine prioritizes: - Consistent rinse power rather than aggressive cutting force - Safe operation on delicate surfaces

ESP10D240V3

$9,594.99

EMAX ESP10D240V3: The flagship of the dual-pump series, this 3-phase 240-gallon unit offers the highest storage capacity and performance for heavy-duty industrial automation. - Motor Specs: 10.0 HP 3-Phase - Flow Capacity: 962 L/min (34 CFM @ 100 PSI) - Force Rating: 175 PSI (12 Bar) - Cylinder Siz

ESP10D120V3

$8,169.99

The ESP10D120V3 is designed for high-demand industrial environments where multiple pneumatic tools operate simultaneously. Compared to single-phase Silent Air models, the 3-phase configuration provides: - Smoother power delivery and higher efficiency - Better performance under continuous load - Red

ESP10A120V1

$8,435.99

The ESP10A120V1 is designed for high-demand shops where airflow stability and reduced noise are equally important. Compared to 80-gallon versions, the key advantage is its larger air reservoir, which provides: - Longer tool runtime before compressor restart - Reduced cycling frequency (less wear on

ESP10A080V1

$8,976.99

The ESP10A080V1 is designed for high-output workshop environments where noise control matters. Compared to standard 10 HP compressors, its key advantage is not only airflow but also: - Much lower intake noise (the loudest part of piston compressors) - Stable high-volume airflow (~38 CFM class) - Re

ESP05V080I1PK

$3,001.99

The ESP05V080I1PK is designed for quiet, stable, and clean compressed air delivery in professional environments. Typical applications: - Automotive workshops - Tire and detailing shops - Small fabrication facilities - Paint and finishing systems - Light industrial maintenance - Shops requiring qui

ES10V080V1

$2,583.99

The ES10V080V1 is designed for high-output shop environments where noise reduction is important. Compared to standard 10 HP piston compressors, it offers: - Much lower perceived noise (intake silencing system) - Stable airflow for multiple pneumatic tools - Reduced vibration due to low-RPM pump ope

ERIK150003

$13,964.99

The ERIK150003 is designed for continuous industrial air demand, where piston compressors would fail due to cycling limits and heat buildup. The rotary screw system provides: - Constant airflow without pressure dips - No start/stop cycling (reduces wear significantly) - High efficiency at long runt

ERI0050801

$5,699.99

The ERI0050801 is designed for constant air demand environments, where piston compressors would normally cycle on and off. Instead, the rotary screw system: - Produces steady, non-pulsating airflow - Eliminates frequent start/stop cycling - Reduces mechanical wear and heat stress - Improves efficie

ERI0050001

$4,369.99

The ERI0050001 is designed for steady, non-stop air demand, which is where rotary screw technology performs best. Instead of cycling on and off like piston compressors, it runs continuously at controlled RPM, providing: - Stable airflow without pressure spikes - Lower noise compared to reciprocatin

EI07V080V1

$3,941.99

The EI07V080V1 is built for serious shop air demand, offering significantly higher airflow than typical 7.5 HP compressors. Its strength comes from: - High airflow (~31 CFM) suitable for multiple pneumatic tools - Two-stage compression for improved efficiency and cooler operation - Pressure-lubrica

EGES24120T

$6,174.99

The EGES24120T is designed for high-demand jobsite air systems, capable of running multiple pneumatic tools simultaneously. Its major advantage is the combination of: - Very high airflow (near 60 CFM class) - Large 120-gallon storage buffer - Gas engine independence (no electrical supply required)

EGES1860ST

$7,599.99

The EGES1860ST is built for serious mobile air demand, especially where multiple pneumatic tools must run simultaneously. Its high CFM output allows it to support: - Framing nailers and roofing tools - Impact wrenches and air ratchets - Light sandblasting setups - Industrial maintenance tools in th

DXCMV7518075

$2,127.99

The DXCMV7518075 is designed for serious workshop air demand, bridging the gap between small shop compressors and full industrial screw systems. Its performance strengths include: - Stable airflow for multiple pneumatic tools at once - High-pressure storage (175 PSI) for longer tool runtime - Lowe

DXCMV5048055.1

$1,595.99

The DXCMV5048055.1 is designed for serious shop workloads, not light DIY use. Its combination of high CFM output and large air storage capacity allows it to: - Run multiple pneumatic tools at the same time - Maintain stable pressure under intermittent heavy load - Reduce compressor cycling due to l

DXCMV5018055

$2,516.99

The DXCMV5018055 is built for users who need serious shop air capacity without moving into large industrial screw compressor systems. Its biggest advantage is its high airflow for a 5 HP class compressor (~18 CFM) combined with a large 80-gallon tank, which helps: - Reduce pressure drops during too

DXCMTA1980854.SAN

$599.99

Dewalt DXCMTA1980854.SAN: Built for job-site mobility, this wheelbarrow-style compressor provides a low center of gravity and rugged pneumatic tires for easy transport over rough terrain. - Drive Strength: 1.9 HP Electric Motor - Airflow Volume: 170 L/min (6.0 SCFM @ 90 PSI) - Pressure Peak: 150 PS

DXCMLA4708065

$1,215.99

The DXCMLA4708065 is designed for steady, continuous shop air supply rather than peak portable performance. Its strength lies in its large tank capacity combined with a low-RPM cast iron pump, which allows it to: - Maintain stable pressure during tool use - Reduce compressor cycling frequency - Sup

DXCMH1393075

$2,293.99

The DXCMH1393075 is designed for field operations where electrical power is unavailable or impractical. Its main strength is high airflow in a portable gas-driven platform, allowing it to run multiple pneumatic tools at the same time. Key performance characteristics: - Strong airflow for framing,

DXCM602

$637.99

The DXCM602 is built around a high-pressure single-stage system, which gives it a key advantage: it stores more usable air in the tank compared to lower-pressure 135 PSI compressors. This helps reduce compressor cycling and improves tool runtime between refills. However, its real performance streng